smartd_log plugin: configuration file added

diff --git a/conf.d/python.d/smartd_log.conf b/conf.d/python.d/smartd_log.conf
new file mode 100644 (file)
index 0000000..e16454d
--- /dev/null
+++ b/conf.d/python.d/smartd_log.conf
@@ -0,0 +1,85 @@
+# netdata python.d.plugin configuration for smartd log
+#
+# This file is in YaML format. Generally the format is:
+#
+# name: value
+#
+# There are 2 sections:
+#  - global variables
+#  - one or more JOBS
+#
+# JOBS allow you to collect values from multiple sources.
+# Each source will have its own set of charts.
+#
+# JOB parameters have to be indented (using spaces only, example below).
+
+# ----------------------------------------------------------------------
+# Global Variables
+# These variables set the defaults for all JOBs, however each JOB
+# may define its own, overriding the defaults.
+
+# update_every sets the default data collection frequency.
+# If unset, the python.d.plugin default is used.
+# update_every: 1
+
+# priority controls the order of charts at the netdata dashboard.
+# Lower numbers move the charts towards the top of the page.
+# If unset, the default for python.d.plugin is used.
+# priority: 60000
+
+# retries sets the number of retries to be made in case of failures.
+# If unset, the default for python.d.plugin is used.
+# Attempts to restore the service are made once every update_every
+# and only if the module has collected values in the past.
+# retries: 5
+
+# ----------------------------------------------------------------------
+# JOBS (data collection sources)
+#
+# The default JOBS share the same *name*. JOBS with the same name
+# are mutually exclusive. Only one of them will be allowed running at
+# any time. This allows autodetection to try several alternatives and
+# pick the one that works.
+#
+# Any number of jobs is supported.
+#
+# All python.d.plugin JOBS (for all its modules) support a set of
+# predefined parameters. These are:
+#
+# job_name:
+#     name: myname     # the JOB's name as it will appear at the
+#                      # dashboard (by default is the job_name)
+#                      # JOBs sharing a name are mutually exclusive
+#     update_every: 1  # the JOB's data collection frequency
+#     priority: 60000  # the JOB's order on the dashboard
+#     retries: 5       # the JOB's number of restoration attempts
+#
+# Additionally to the above, smartd_log also supports the following:
+#
+#    log_path: '/path/to/smartdlogs'   # path to smartd log files. Default is /var/log/smartd
+#    raw_values: no                    # raw or normalized values on charts. Default is normalized.
+#    smart_attributes: '1 2 3 4 44'    # add additional smart attributes charts. Default are ['1', '4', '5', '7', '9', '12', '193', '194', '197', '198', '200'].
+#
+# ----------------------------------------------------------------------
+# Additional information
+#  Plugin reads smartd log files (-A option). 
+#  You need to add (man smartd) to /etc/default/smartmontools '-i 600 -A /var/log/smartd/' to pass additional options to smartd on startup
+#  Then restart smartd service and check /path/log/smartdlogs
+#  ls /var/log/smartd/
+#  CDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv  WDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv  ZDC_WD10EZEX_00BN5A0-WD_WCC3F7FLVZS9.ata.csv
+#
+# Smartd APPEND logs at every run. Its NOT RECOMMENDED to set '-i' option below 60 sec.
+# STRONGLY RECOMMENDED to create smartd conf file for logrotate
+#
+# RAW vs NORMALIZED values
+# "Normalized value", commonly referred to as just "value". This is a most universal measurement, on the scale from 0 (bad) to some maximum (good) value.
+# Maximum values are typically 100, 200 or 253. Rule of thumb is: high values are good, low values are bad.
+# 
+# "Raw value" - the value of the attribute as it is tracked by the device, before any normalization takes place.
+# Some raw numbers provide valuable insight when properly interpreted. These cases will be discussed later on.
+# Raw values are typically listed in hexadecimal numbers. The raw value has different structure for different vendors and is often not meaningful as a decimal number.
+#
+#
+# JOB configuration
+# 
+log_path: '/var/log/smartd'